启闭机闸门的安装-冀州最好的启闭机销售及维修的厂家
联系我们
联系人:南经理
手机:13932899771 15612833218
电话/传真:0318-8830218
邮箱:706843811@qq.com
地址:河北省冀州市西王工业区
当前位置:首页 >>新闻中心 >> 启闭机闸门的安装

启闭机闸门的安装 The installation of the gate of the opening and closing machine 1. 安装前,要首先检查竖框与横框之间、闸板与闸板之间(指多块闸板组合的闸门)的连接螺丝,是否在运输装卸中引起松动,它们的接茬处是否错牙,要调整成一个平面,然后上紧螺栓。 Before the 1. installation, we should first check the connection screws between the vertical frame and the cross frame, between the gate and the gate (the gate of the multiple sluice), whether it is loose in the handling of the transportation, whether their picking place is wrong, to be adjusted to a plane, and then to tighten the bolt. 2. 安装时,将闸门整体竖入闸槽,在两边立框的下面垫上调整垫块(严禁垫下横梁),两立框用手动葫芦和斜拉立稳,将闸门找直找平,各地脚孔内串上地脚螺栓,支好盒子进行一期浇注,注意混凝土不能埋上闸框,使闸框底平面贴在水泥墙上,当混凝土凝固后,再对闸框进行调整,拧紧地脚螺栓,对启闭机闸门进行调整时,在启闭机闸门背面的闸板和闸框的封水处,用塞尺对四周进行间隙测量,如有大于0.3mm的地方,在该处闸框与混凝土墙间强塞铁片,消除间隙,然后调整至四周间隙都在0.3mm以下,再进行二期浇注,混凝土将闸框埋入二分之一处为宜。 When the 2. is installed, the gate is put into the sluice slot as a whole, and the cushion block is adjusted on the underneath of the two sides of the vertical frame (strictly prohibit the cross beam). The two erect frames use manual gourd and slanted to hold the stable, the gate is leveled straight, the foot bolts on the foot holes in all parts of the foot are strung up the foot bolts and the box is poured for a period of pouring, and the concrete can not be buried on the gate frame to make the bottom plane of the gate frame. It is attached to the cement wall. When the concrete is solidified, the gate frame is adjusted and the foot bolt is tightened. When the gate of the opening and closing machine is adjusted, the clearance is measured at the sealing water of the gate and the gate on the back of the opening and closing gate. If there is a place greater than 0.3mm, the sluice block and the concrete wall are strongly slug between the concrete wall. To eliminate clearance, then adjust to the gap below 0.3mm, then do two stage casting, and the concrete will be embedded in 1/2 parts. 3. 浇注混凝土时,流进闸板、闸框、斜铁、档板间的灰浆应彻底清除,以防止灰浆凝固后影响启闭机闸门启闭。 3. when pouring concrete, the mortar flowing into the gate, gate frame, diagonal iron and baffle plates should be thoroughly removed, so as to prevent the mortar from solidifying and affect the opening and closing of the hoist gate. 4. 清除加固物。启闭机闸门出厂前,为使闸板、闸框贴合紧凑,安装后减少间隙,2m以上的闸门在上下横框上安装了4-6个勾板压铁,立框的档板上增加了顶丝,注意在间隙调整后,将勾板压铁和顶丝拆除,以便启闭机闸门的闸门启闭。 4. remove the reinforcement. Before the sluice gate is out of the factory, in order to make the gate and gate close compact and reduce the gap after installation, the gate above 2m is installed 4-6 hook plates on the upper and lower cross frame, and the top wire is added to the frame of the frame.

版权所有 © 河北省衡水市博宇水工机械厂
联系人:南经理 手机:13932899771 15612833218 电话/传真:0318-8830218 邮箱:706843811@qq.com 地址:河北省冀州市西王工业区
水利机械推荐:启闭机、螺杆启闭机,卷扬启闭机、启闭机闸门、铸铁闸门、钢制闸门、清污机、拦污栅、橡胶止水等 网址:www.gkjjt.com
友链:
幸运农场官网 北京赛车 幸运农场开奖走势 幸运农场高手交流群 北京赛车PK10 重庆幸运农场平台 幸运农场开奖直播 北京赛车PK10 北京赛车PK10计划